Outcome-based 19/SU Course Syllabus
  
Course Rubric Number Section: ABDR 1359 2001
Lecture-Lab-Credit: --3
CIP Code: 47..060
Course Title: Sheet Metal Fabrication I
Course Description: A study of the basic shaping techniques required for fabricating sheet metal parts and pieces. Discussion will include custom cars and street rods.
Prerequisites:
Co-requisites:
Course Meets: 200F 109 LEC TH 16:00:00 17:20:00 200F 109 LEC F 09:30:00 10:40:00 200F 112 LAB F 10:40:00 13:00:00 200F 112 LAB F 13:10:00 14:50:00
  
Instructor: Joseph Cantu
Office Phone Number: 956-364-4825
Email Address: jcantu18@tstc.edu
Office Fax Number: 956-364-5159
Building & Office Room Number: F 109
Office Hours: M-W-F 8-9am
 
Approved by: Clint CampbellDate: 2019-04-26
Course Outcomes
CO1: Perform basic sheet metal forming techniques
CO2: Shape sheet metal parts to conform with the specific design of the automobile
CO3: Install the fabricated sheet metal part
 

TSTC Grading Policy

(Grades for courses must be C or better)

Grade

Percent

Description

Grade Points

A

90-100

Excellent/Superior Performance Level

4

B

80-89

Above Required Performance Level

3

C

70-79

Minimum Required Performance Level

2

D

60-69

Below Required Performance Level

1

F

Below 60

Failure to meet Performance Requirements

0

IP

--

In Progress

 

W

--

Withdrawal

0

CR

--

Credit

0

AUD

--

Audit of Course

0

See College Catalog for complete descriptions.

 

Competencies Rating Scale

Rating Scale Key

 

 

 

6

90+

Proficient

Student consistently performs the task accurately to industry standards without supervision.

5

80-89

Proficient

Student performs the task to industry standards with no supervision.

4

70-79

Proficient

Student performs the task to industry standards with little supervision. This is the minimum performance rating for STAR skill completion.

3

60-69

Exposed/Not Proficient

Student has been introduced to the task and can perform some of the tasks to industry standards.

2

50-59

Exposed/Not Proficient

Student has been introduced to the task, but cannot perform the task to industry standards.

1

0-49

 

Student was absent or did not complete assignment.

 

Campus Standard Policies

The Student Handbook contains valuable information on campus policies and procedures.

  • Student Code of Conduct
  • Student Drug and Alcohol Testing Policy
  • Plagiarism
  • Student Grievances and Complaints

 

Safety

Safety is always a priority and it is everyone’s responsibility. A hazard assessment must be performed prior to each laboratory assignment in order to identify potential risks and the appropriate safety measures to be used in the mitigation/elimination of identified hazards.

 

Disability Services

Any student who, because of a disability, may require special accommodations in order to meet the course requirements, should contact the Disability Services office, as soon possible, to make necessary arrangements.  Please note that instructors are not allowed to provide classroom accommodation to a student until appropriate verification from the Disability Services office has been provided.

Abilene Campus
Amy Buchanan
Testing and Support Services
Abilene Main Campus Bldg. Rm. 112
325-734-3653

Breckenridge Campus
Lisa Langford
Testing and Advisement located in
The Main Building Rm. 106
254-559-7731

Brownwood Campus
Nicole Whitley
Testing and Advisement
Building 2 Rm. 120
325-641-5955
Fort Bend Campus
Georgeann Calzada
Enrollment Suite, Brazos Center, Rm. 106
346-239-3422

Harlingen Campus
Corina De La Rosa
Disability Services
Student Support Services
Student Services Bldg. Rm. 216
956-364-4521

Marshall Campus
Annette Ellis
Administration and Admissions Rm. 150
909-923-3313
Sweetwater Campus
Patricia Carpio
Disability Services
Student Support Services
Lance Sears Building Rm. 140
325-235-7441

North Texas Campus
Amanda Warren
Student Services, Room 227
972-617-4724

Waco Campus
Marilyn Harren
Disabilities Services Office
Student Services Center Rm. 198
254-867-3600

Williamson County
Chemese Armstrong
Enrollment Services Rm. B113C
512-759-5907

 

Tutoring Statement

The Supplemental Instruction & Tutoring Program at TSTC offers free tutoring and academic support services to help you achieve your academic and career goals.  You can access the Tutoring Schedule, as well as MyTSTC Video Tutor Library, by visiting: https://portal.tstc.edu/student/Student_Learning/Pages/Tutoring.aspx 
(shortened link: goo.gl/Z9vJvY ). 
For more information, please contact Norma A. Salazar@ 956-364-4557.

Learning Resource Center

The purpose of the TSTC Learning Resource Center is to serve the TSTC Community and support academic, advanced, specialized and emerging programs, contributing to the educational and economic development of the State of Texas. For access to online library resources, databases and services visit the Learning Resource Center on the TSTC Portal or go to tstc.libguides.com.


Resources
Tools, Materials:
ItemResource Quantity
1Safety Glasses1
212" Locking Wing Divider1 Harbor Freight 96440
3Tape Measure Metric 10'/3M1
4Thin Soft Leather Gloves1 pair
5Swivel Head Deburring Tool1 General Tool 482 or Sears
6Red or Black Sharpie Fine Point2
7Push Pin Magnets 10pc Set1 Home Depot 07509 or similar item
8Spiral Notebook1
9Pencils and Pens2 ea
10Nitrile Gloves or 1pr of Solvent Gloves10pr
11Ear Plugs1pr

 

Grade Scheme
Category Description Category Value   
Test 20%   
Assessment Label: Assessment Description Assessment Value
Test Dust Pan:Turn in Dust Pan finished or not.4.00%
Test Shrinker/Stretcher:Test on S-Shape Panel on English wheel and Shrinker / Stretcher4.00%
Test Practice Panel:Turn in Practice panel finished or not.4.00%
Test on S-Shape piece:Test on S-Shape piece, create flames on piece and turn in.4.00%
Final Exam:Motorcycle fender must fit criteria and over tire.4.00%
Category Description Category Value   
Lab 80%   
Assessment Label: Assessment Description Assessment Value
Identify Safety in shop:Lab Safety in shop6.67%
Simple Template:Create paper template for practice panel. Create paper template for dust pan.6.67%
Aviation Tin Snips :Demonstrate use of Aviation Tin Snips Students practice use of snips to trim sheet metal6.67%
English Wheel:Panel shaped on English Wheel fits Templates6.67%
Complete S-Shape Piece:Complete S-Shape Piece for next week6.67%
Complete Practice Panel: Complete Practice Panel for next week6.67%
Lab Project:Continue work with assigned projects6.67%
Lab Project cont.:Continue work with assigned projects6.67%
Lab projects:Continue work with assigned projects6.67%
Aluminum :Create metal shape using bead roller using aluminum panel to match aluminum template.6.67%
Patch Panel:Create a replacement patch panel on assigned vehicle area6.67%
Motorcycle fender: Finish projects assigned6.67%
Total Assessment Percent          100.00%
Total Category Percent 100.00%
A = 100-90 B = 89-80 C = 79-70 D = 69-60 F = 59-0


Description of Graded Elements of the Course
Assessment Label Assessment Description/Course outcomes met Assessment Value
in Percent
% of Final Grade
Identify Safety in shopLab Safety in shop
Course outcomes met: CO1, CO2, CO3
6.676.67%
Simple TemplateCreate paper template for practice panel. Create paper template for dust pan.
Course outcomes met: CO1
6.676.67%
Aviation Tin Snips Demonstrate use of Aviation Tin Snips Students practice use of snips to trim sheet metal
Course outcomes met: CO1
6.676.67%
English WheelPanel shaped on English Wheel fits Templates
Course outcomes met: CO1
6.676.67%
Complete S-Shape PieceComplete S-Shape Piece for next week
Course outcomes met: CO1
6.676.67%
Test Dust PanTurn in Dust Pan finished or not.
Course outcomes met: CO1
4.004.00%
Complete Practice Panel Complete Practice Panel for next week
Course outcomes met: CO1
6.676.67%
Test Shrinker/StretcherTest on S-Shape Panel on English wheel and Shrinker / Stretcher
Course outcomes met: CO1
4.004.00%
Lab ProjectContinue work with assigned projects
Course outcomes met: CO3, CO1, CO2
6.676.67%
Test Practice PanelTurn in Practice panel finished or not.
Course outcomes met: CO1
4.004.00%
Lab Project cont.Continue work with assigned projects
Course outcomes met: CO2, CO1, CO3
6.676.67%
Lab projectsContinue work with assigned projects
Course outcomes met: CO3, CO1, CO2
6.676.67%
Aluminum Create metal shape using bead roller using aluminum panel to match aluminum template.
Course outcomes met: CO2, CO1
6.676.67%
Patch PanelCreate a replacement patch panel on assigned vehicle area
Course outcomes met: CO1, CO3
6.676.67%
Motorcycle fender Finish projects assigned
Course outcomes met: CO2, CO3, CO1
6.676.67%
Test on S-Shape pieceTest on S-Shape piece, create flames on piece and turn in.
Course outcomes met: CO1, CO3
4.004.00%
Final ExamMotorcycle fender must fit criteria and over tire.
Course outcomes met: CO3, CO2
4.004.00%
  100.00100.00%

 

Course Schedule
Unit/
Week
Unit Description/Objectives Assessment Label:Description Due Date
1Week 1: Introduction of Course Syllabus and Requirements
 
  • Summarize the contents of the course syllabus as discussed in student orientation.
  • Identify course assessments, policies and procedures using syllabus.
  • Tour lab and discuss safety and proper use of equipment.
Identify Safety in shop: Lab Safety in shopEnd of Class
2Week 2: How to Create a Template
 
  • Identify tools and materials need to create a template.
    Identify and perform steps on a template to create the practice panel.
  • Discuss operation of the English wheel
Simple Template: Create paper template for practice panel.
Create paper template for dust pan.
End of Class
Aviation Tin Snips : Demonstrate use of Aviation Tin Snips
Students practice use of snips to trim sheet metal
3Week 3:How to use the English Wheel
 
  • Discuss proper operation of the English Wheel.
    Identify correct and incorrect tracking of the English Wheel.
  • Perform panel shaping to fit dust pan template using the English Wheel.
    Discuss operation of Sheet Metal Break
English Wheel: Panel shaped on English Wheel fits Templates
4Week 4: How to use a sheet metal brake
 
  • Identify and practice proper use of a sheet metal brake.
    Identify limitations of the sheet metal brake.
    Identify sheet metal thickness or gauge.
    Discuss sheet metal composition.
  • Create the practice panel using template created in week 2
    Discuss operation of Shrinker/ Stretcher
Complete S-Shape Piece: Complete S-Shape Piece for next week
Test Dust Pan: Turn in Dust Pan finished or not.
5Week 5: How to Use a Shrinker/ Stretcher
 
  • Discuss how metal moves as it shrinks or stretches.
    Identify if the metal needs to shrink or stretch to match desired shape.
  • Perform shrinking/ stretching of panel to fit template.
    Discuss operation of Bead Roller
Complete Practice Panel: Complete Practice Panel for next week
Test Shrinker/Stretcher: Test on S-Shape Panel on English wheel and
Shrinker / Stretcher
6Week 6: How to use the Bead Roller
 
  • Discuss operation of the bead roller and die profiles.
    Identify which dies create which profile.
  • Shape panel using the bead roller to match template
Lab Project: Continue work with assigned projects
Test Practice Panel: Turn in Practice panel finished or not.
7Week 7: Discuss on how to make a motorcycle fender.
 
  • Discuss step by step on how to make a motorcycle fender.
  • Shape panel using the bead roller and Shrinker/ Stretcher
Lab Project cont.: Continue work with assigned projectsIn Class
8Week 8: Discuss principles of metal shaping.
 
  • Identify high crowns, low crowns, style lines and, reverses
  • Practice proper and safe use of equipment while shaping metal.
Lab projects: Continue work with assigned projectsIn Class
9Week 9:Discuss other ideas for shaping metal
 
  • Identify other metal shaping equipment and techniques
  • Continue practicing proper and safe use of equipment while shaping parts.
Aluminum : Create metal shape using bead roller using aluminum panel to match aluminum template.
10Week 10:Discuss Creating Complex parts using various tools
 
  • Create several templates using metal and paper
Patch Panel: Create a replacement patch panel on assigned vehicle area
11Week 11:Last day to complete work
 
  • Complete any unfinished lab projects today
  • Students will turn in all work by end of class completed or not.
Motorcycle fender: Finish projects assigned
Test on S-Shape piece: Test on S-Shape piece, create flames on piece and turn in.In Class
12Week 12: Final Exam: Motorcycle fender
Lab Clean Up and Awards Ceremony
 
  • Students will clean lab, equipment and attend the Awards Ceremony.
Final Exam: Motorcycle fender must fit criteria and over tire.In Class

 

Daily, Weekly, Assignments and Participation Grades:
 
A class participation grade will be taken each and every class day. The quiz or assignment will be the participation grade if given. Otherwise, 25 will be given for attending and being on time. A 12.5 will be given if you are tardy. An unexcused absence will earn a grade of “ZERO”. The Midterm and Final Exams will include the participation grade for those days. 25% of the exam grade will be deducted if you are tardy. A grade of “ZERO” will be earned if you have an unexcused absence.

                                                                   

Participation Policy

A Student is expected to attend and participate during the scheduled period of instruction (lecture and lab). This begins with the first scheduled class day of the term. A student deemed a non-participant for more than 10% ( 1.5     days) of the lecture or 10% (1.5      days) of the lab periods, regardless of grades earned on assignments, will have to repeat the course. 
 
A student is considered tardy up to 15 minutes into the scheduled lecture or lab, and thereafter will be considered a non-participant for that period of instruction.
 
A sum of two tardies is equivalent to one non- participation period.

 

 Safety Procedures

Students are required to participate in a safety lecture prior to performing in the laboratory portion of the course. A written test will be given to each participating student covering the presented safety materials. Students must complete the safety test with 100% accuracy prior to receiving lab assignments.
 
All lecture and laboratory safety rules and regulations will be followed in every detail. Failure to comply with this policy will result in dismissal from class until further notice.

 

Pop Tests
 
Can be given at any time by the instructor and are not make up items.

 

 

Exemptions
 
Students can be exempted from a final exam if:
A.    Lecture average is 90 or above
B.     Attendance is perfect
C.     Assignments are completed and turned in
 
Cell phone Policy
 
Cell phones may be brought into the classroom or lab. However, they must be in the off or vibrate position.
 
Anyone failing to adhere to this policy will be dismissed from class and issued a non-participation grade (absence) for that period of instruction.
 

 

Departmental Awards Ceremony/Cleanup Policy
 
Each student is expected to participate in the awards ceremony and cleanup activities once the date has been identified.
 
Students’ final exam grade is dependent upon their participation at these functions. One half (½) of the final exam grade for the course is participation. One half (½) of the final exam grade is completing the final exam for the course.
 
Students with unexpected circumstances can be excused by the department chair only.
 
TSTC school calendar identifies the end of the semester. Student break begins the day after.